NXP公司的UBA2016A/15/15A 是具有PFC,線性調光和升壓功能的600V熒光燈驅動器.IC包含了熒光燈控制模塊,半橋驅動器,內置了臨界導電模式PFC控制器/驅動器和多種保護機制,電源電壓高達600V,火線電壓高達390V.本文介紹了UBA2016A/15/15A主要特性和優勢,方框圖, 基本的PFC應用框圖以及多種TL或CFL應用電路, UBA2016AT HFTL演示板主要指標,框圖,電路圖和材料清單與PCB布局圖.

UBA2016A/15/15A:600 V fluorescent lamp driver with PFC, linear dimming and boost function

The UBA2016A/15/15A are high voltage Integrated Circuits (IC) intended to drive fluorescent lamps with filaments such as Tube Lamps (TL) and Compact Fluorescent Lamps (CFL) in general lighting applications. The IC comprises a fluorescent lamp control module, half-bridge driver, built-in critical conduction mode Power Factor Correction (PFC) controller/driver and several protection mechanisms. The IC drives fluorescent lamp(s) using a half-bridge circuit made of two MOSFETs with a supply voltage of up to 600 V.

The UBA2016A/15/15A are designed to be supplied by a start-up bleeder resistor and a dV/dt supply from the half-bridge circuit, or any other auxiliary supply derived from the half-bridge or the PFC. The supply current of the IC is low. An internal clamp limits the supply voltage.

UBA2016A/15/15A主要特性和優勢:

Power factor correction features:

Integrated 4-pin critical conduction mode PFC controller/driver

Open and short pin-short protection on PFC feedback pin

Overcurrent protection

Overvoltage protection

Half-bridge driver features:

Integrated level-shifter for the high-side driver of the half-bridge

Integrated bootstrap diode for the high-side driver supply of the half-bridge

Independent non-overlap time

Fluorescent lamp controller features:

Linear dimming (UBA2016A and UBA2015A only)

EOL (End-Of-Life) detection (both symmetrical and asymmetrical)

Adjustable preheat time

Adjustable preheat current

Adjustable fixed frequency preheat (UBA2015 and UBA2015A only)

Lamp ignition failure detection

Ignition detection of all lamps fat multiple lamps with separate resonant tanks

Second ignition attempt if first failed

Constant output power independent of mains voltage variations

Automatic restart after changing lamps

Adjustable lamp current boost at start-up (UBA2016A only)

Lamp current control

Enable input (UBA2015 and UBA2015A only)

Protection

Hard switching/capacitive mode protection

Half-bridge overcurrent (coil saturation) protection

Lamp overvoltage (lamp removal) protection

Temperature protection

UBA2016A/15/15A應用:

Intended for fluorescent lamp ballasts with either a dimmable (UBA2016A and UBA2015A) or a fixed (UBA2015) output and PFC for AC mains voltages of up to 390 V.

圖1.UBA2016AA方框圖

圖2.UBA2015/15A方框圖

圖3.UBA2016A/15/15A基本的PFC應用框圖

圖4.UBA2016A用于TL或CFL的應用電路圖(火線濾波器未顯示)

圖5.UBA2016A有較好PFC性能的TL或CFL的應用電路圖(火線濾波器未顯示)

圖6.UBA2016A帶固定升壓時間的TL或CFL的應用電路圖(火線濾波器未顯示)

圖7.UBA2016A帶燈溫度升壓起動的TL或CFL的應用電路圖(火線濾波器未顯示)

圖8.UBA2016A調光TL應用電路圖(火線濾波器未顯示)

帶升壓和調光的UBA2016AT HFTL演示板

This User manual describes a demonstration (demo) board with boost and dimming functionality using the UBA2016AT controller. The demo board drives a 28 W 2D (square) fluorescent lamp.


圖9.UBA2016AT HFTL演示板外形圖
UBA2016AT HFTL演示板主要指標:


圖10.UBA2016AT HFTL演示板框圖


圖11.UBA2016AT HFTL演示板電路圖
UBA2016AT HFTL演示板材料清單(BOM):





圖11.UBA2016AT HFTL演示板PCB布局圖
詳情請見:
http://www.nxp.com/documents/data_sheet/UBA2016A_15_15A.pdf
和
http://www.nxp.com/documents/user_manual/UM10359.pdf