</a>心電圖" title="心電圖">心電圖" title="心電圖">心電圖模擬前端(ECG FE),集成了可同時取樣的24位delta-sigma (ΔΣ) ADC和可編增益放大器(PGA),基準電壓源和板上振蕩器.每路的功耗僅為335uW,輸入參考噪音8 μVPP (150-Hz BW, G = 6),輸入偏置電流200pA,數據速率從125SPS到8kSPS,CMMR為-105dB,可編程增益1, 2, 3, 4, 6, 8或12,支持單電源和雙極電源,主要用在便攜式低功耗醫用心電圖儀,運動和健美等領域.本文介紹了ADS1x9x主要特性, 功能方框圖, 單電源和雙極電源工作電路圖, ADS1x9xECG-FE演示板主要特性,方框圖,電路圖,材料清單和PCB元件布局圖.
Low-Power, 2-Channel, 24-Bit Analog Front-End for Biopotential Measurements
The ADS1291, ADS1292, and ADS1292R are multichannel, simultaneous sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converters (ADCs) with a built-in programmable gain amplifier (PGA), internal reference, and an onboard oscillator.
The ADS1291, ADS1292, and ADS1292R incorporate all features commonly required in portable, low-power medical electrocardiogram (ECG), sports, and fitness applications. ADS1292R enable the creation of scalable medical instrumentation systems at significantly reduced size, power, and overall cost.
The ADS1291, ADS1292, and ADS1292R have a flexible input multiplexer per channel that can be independently connected to the internally-generated signals for test, temperature, and lead-off detection. Additionally, any configuration of input channels can be selected for derivation of the right leg drive (RLD) output signal.
The ADS1292R version includes a fully integrated respiration impedance measurement The devices are packaged in a 5-mm × 5-mm, 32-pin thin quad flat pack (TQFP). Operating temperature is specified from –40℃ to +85℃.
ADS1x9x主要特性:
• Two Low-Noise PGAs and Two High-Resolution ADCs (ADS1292 and ADS1292R)
• Low Power: 335 μW/channel
• Input-Referred Noise: 8 μVPP A(150-Hz BW, G = 6)
• Input Bias Current: 200 pA.
• Data Rate: 125 SPS to 8 kSPS
• CMRR: –105 dB
• Programmable Gain: 1, 2, 3, 4, 6, 8, or 12
• Supplies: Unipolar or Bipolar
– Analog: 2.7 V to 5.25 V
– Digital: 1.7 V to 3.6 V
• Built-In Right Leg Drive Amplifier, Lead-Off Detection, Test Signals t
• Integrated Respiration Impedance Measurement (ADS1292R)
• Built-In Oscillator and Reference
• Flexible Power-Down, Standby Mode
• SPI™-Compatible Serial Interface.
• Operating Temperature Range: –40℃ to +85℃
ADS1x9x應用:
• Medical Instrumentation (ECG) including:
– Patient monitoring: Holter, event, stress, and vital signs including ECG, AED, and Telemedicine
– Sports and fitness (heart rate, respiration, and ECG)
• High-Precision, Simultaneous, Multichannel Signal Acquisition
圖1.ADS1x9x功能方框圖
圖2.ADS1x9x單電源工作電路圖
圖3.ADS1x9x雙電源工作電路圖
ADS1x9xECG-FE演示板
This demonstration kit models the ADS1192, ADS1292 and ADS1292R. The family of devices are two-channel, 16/24-bit, low-power, integrated analog front-end (AFE) designed for portable electrocardiogram (ECG) and respiration applications. The ADS1x9xECG-FE is intended for prototyping and evaluation. This user’s guide includes a complete circuit description, schematic diagram, and Bill of Materials.
The ADS1x9xECG FE is a demonstration kit for the ADS1292R, a two channel, simultaneous sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converter (ADC) with a built-in programmable gain amplifier (PGA), internal reference, and respiration measurement. The ADS1292R chip incorporates all of the features that are commonly required in medical electrocardiogram (EKG/ECG) and electroencephalogram (EEG) and respiratory monitoring applications. The ADS1x9xECG FE is equipped with a MSP430F5529 micro-controller giving the user all the circuitry needed to run the ADC. The board can be used with a variety of patient simulators and allows the user to take advantage of the flexible input multiplexer which can be independently connected to the internally-generated signals for test, temperature, and lead-off detection. Software is available from Texas Instruments to allow the evaluation platform to run with a PC user interface.
ADS1x9xECG-FE演示板主要特性:
Easy-to-use evaluation software for Microsoft™ Windows XP or Windows 7
Built-in analysis tools including oscilloscope, FFT, and histogram displays
Flexible input configurations
Integrated Respiration Impedance
Digital Low Pass, High Pass, and 50/60Hz notch filters for post processing
Real time data streaming from the demo board to the PC
Ability to export data in simple test files for post processing
圖4. ADS1x9xECG-FE演示板外形圖
The board can be assembled with any of these chips. ADS1292, ADS1292R and ADS1192 demonstration kits are available. The MSP430 firmware and PC application are designed to automatically detect the installed part and configure to accommodate the part.
該版本所支持的特性:
1. Four electrode ECG cable support
2. View six ECG Leads: Lead I, Lead II, Lead III, Lead aVR, Lead aVL, Lead aVF and respiration channel (ADS1292R only) .
3. Two modes of operation: Evaluation and Live ECG / Respiration
4. Acquire data at up to 8 kHz in Evaluation mode
5. Current based Lead off detection
6. USB based power and PC application connectivity
7. Access to all ADS1x9x registers via an easy to use GUI.
8. Built-in time domain, histogram, FFT and ECG / Resp related analysis on the PC application
9. Live ECG with heart rate calculation.
10. Live Respiration wave with respiration rate calculation
11. USB based firmware upgrade option
12. MSP430 Firmware debugging using ez430 USB emu
ADS1x9xECG-FE演示板主要特性:
The key features of the ADS1x9x analog front end demonstration board are:
• Based on MSP430F5529
• ADS1192 and ADS1292 suitable for six leads of ECG: Lead I, Lead II, Lead III, Lead aVR, Lead aVL, or Lead aVF
• ADS1292R suitable for one lead of ECG (Lead I) and respiration channel
• Low power consumption (350 Micro Watt/channel)
• Data Rate ranges from 125 SPS to 8 kSPS
• Unipolar Operation
• Lead off detection circuitry
• On chip oscillator and reference
• On chip RLD amplifier
• SPI data interface
• 8Gb NAND Flash support
圖5.ADS1x9xECG-FE演示板框圖
圖6.ADS1x9xECG-FE演示板電路圖(1)
圖7.ADS1x9xECG-FE演示板電路圖(2)
圖8.ADS1x9xECG-FE演示板電路圖(3)
圖9.ADS1x9xECG-FE演示板電路圖(4)
圖10.ADS1x9xECG-FE演示板電路圖(5)
圖11.ADS1x9xECG-FE演示板電路圖(6)
ADS1x9xECG-FE演示板材料清單(BOM):
圖12.ADS1x9xECG-FE演示板元件布局圖:頂層
圖13.ADS1x9xECG-FE演示板元件布局圖:底層
詳情請見:
http://www.ti.com/lit/ds/sbas502a/sbas502a.pdf
和
http://www.ti.com/lit/ug/slau384a/slau384a.pdf
Low-Power, 2-Channel, 24-Bit Analog Front-End for Biopotential Measurements
The ADS1291, ADS1292, and ADS1292R are multichannel, simultaneous sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converters (ADCs) with a built-in programmable gain amplifier (PGA), internal reference, and an onboard oscillator.
The ADS1291, ADS1292, and ADS1292R incorporate all features commonly required in portable, low-power medical electrocardiogram (ECG), sports, and fitness applications. ADS1292R enable the creation of scalable medical instrumentation systems at significantly reduced size, power, and overall cost.
The ADS1291, ADS1292, and ADS1292R have a flexible input multiplexer per channel that can be independently connected to the internally-generated signals for test, temperature, and lead-off detection. Additionally, any configuration of input channels can be selected for derivation of the right leg drive (RLD) output signal.
The ADS1292R version includes a fully integrated respiration impedance measurement The devices are packaged in a 5-mm × 5-mm, 32-pin thin quad flat pack (TQFP). Operating temperature is specified from –40℃ to +85℃.
ADS1x9x主要特性:
• Two Low-Noise PGAs and Two High-Resolution ADCs (ADS1292 and ADS1292R)
• Low Power: 335 μW/channel
• Input-Referred Noise: 8 μVPP A(150-Hz BW, G = 6)
• Input Bias Current: 200 pA.
• Data Rate: 125 SPS to 8 kSPS
• CMRR: –105 dB
• Programmable Gain: 1, 2, 3, 4, 6, 8, or 12
• Supplies: Unipolar or Bipolar
– Analog: 2.7 V to 5.25 V
– Digital: 1.7 V to 3.6 V
• Built-In Right Leg Drive Amplifier, Lead-Off Detection, Test Signals t
• Integrated Respiration Impedance Measurement (ADS1292R)
• Built-In Oscillator and Reference
• Flexible Power-Down, Standby Mode
• SPI™-Compatible Serial Interface.
• Operating Temperature Range: –40℃ to +85℃
ADS1x9x應用:
• Medical Instrumentation (ECG) including:
– Patient monitoring: Holter, event, stress, and vital signs including ECG, AED, and Telemedicine
– Sports and fitness (heart rate, respiration, and ECG)
• High-Precision, Simultaneous, Multichannel Signal Acquisition
圖1.ADS1x9x功能方框圖
圖2.ADS1x9x單電源工作電路圖
圖3.ADS1x9x雙電源工作電路圖
ADS1x9xECG-FE演示板
This demonstration kit models the ADS1192, ADS1292 and ADS1292R. The family of devices are two-channel, 16/24-bit, low-power, integrated analog front-end (AFE) designed for portable electrocardiogram (ECG) and respiration applications. The ADS1x9xECG-FE is intended for prototyping and evaluation. This user’s guide includes a complete circuit description, schematic diagram, and Bill of Materials.
The ADS1x9xECG FE is a demonstration kit for the ADS1292R, a two channel, simultaneous sampling, 24-bit, delta-sigma (ΔΣ) analog-to-digital converter (ADC) with a built-in programmable gain amplifier (PGA), internal reference, and respiration measurement. The ADS1292R chip incorporates all of the features that are commonly required in medical electrocardiogram (EKG/ECG) and electroencephalogram (EEG) and respiratory monitoring applications. The ADS1x9xECG FE is equipped with a MSP430F5529 micro-controller giving the user all the circuitry needed to run the ADC. The board can be used with a variety of patient simulators and allows the user to take advantage of the flexible input multiplexer which can be independently connected to the internally-generated signals for test, temperature, and lead-off detection. Software is available from Texas Instruments to allow the evaluation platform to run with a PC user interface.
ADS1x9xECG-FE演示板主要特性:
Easy-to-use evaluation software for Microsoft™ Windows XP or Windows 7
Built-in analysis tools including oscilloscope, FFT, and histogram displays
Flexible input configurations
Integrated Respiration Impedance
Digital Low Pass, High Pass, and 50/60Hz notch filters for post processing
Real time data streaming from the demo board to the PC
Ability to export data in simple test files for post processing
圖4. ADS1x9xECG-FE演示板外形圖
The board can be assembled with any of these chips. ADS1292, ADS1292R and ADS1192 demonstration kits are available. The MSP430 firmware and PC application are designed to automatically detect the installed part and configure to accommodate the part.
該版本所支持的特性:
1. Four electrode ECG cable support
2. View six ECG Leads: Lead I, Lead II, Lead III, Lead aVR, Lead aVL, Lead aVF and respiration channel (ADS1292R only) .
3. Two modes of operation: Evaluation and Live ECG / Respiration
4. Acquire data at up to 8 kHz in Evaluation mode
5. Current based Lead off detection
6. USB based power and PC application connectivity
7. Access to all ADS1x9x registers via an easy to use GUI.
8. Built-in time domain, histogram, FFT and ECG / Resp related analysis on the PC application
9. Live ECG with heart rate calculation.
10. Live Respiration wave with respiration rate calculation
11. USB based firmware upgrade option
12. MSP430 Firmware debugging using ez430 USB emu
ADS1x9xECG-FE演示板主要特性:
The key features of the ADS1x9x analog front end demonstration board are:
• Based on MSP430F5529
• ADS1192 and ADS1292 suitable for six leads of ECG: Lead I, Lead II, Lead III, Lead aVR, Lead aVL, or Lead aVF
• ADS1292R suitable for one lead of ECG (Lead I) and respiration channel
• Low power consumption (350 Micro Watt/channel)
• Data Rate ranges from 125 SPS to 8 kSPS
• Unipolar Operation
• Lead off detection circuitry
• On chip oscillator and reference
• On chip RLD amplifier
• SPI data interface
• 8Gb NAND Flash support
圖5.ADS1x9xECG-FE演示板框圖
圖6.ADS1x9xECG-FE演示板電路圖(1)
圖7.ADS1x9xECG-FE演示板電路圖(2)
圖8.ADS1x9xECG-FE演示板電路圖(3)
圖9.ADS1x9xECG-FE演示板電路圖(4)
圖10.ADS1x9xECG-FE演示板電路圖(5)
圖11.ADS1x9xECG-FE演示板電路圖(6)
ADS1x9xECG-FE演示板材料清單(BOM):
圖12.ADS1x9xECG-FE演示板元件布局圖:頂層
圖13.ADS1x9xECG-FE演示板元件布局圖:底層
詳情請見:
http://www.ti.com/lit/ds/sbas502a/sbas502a.pdf
和
http://www.ti.com/lit/ug/slau384a/slau384a.pdf
本站內容除特別聲明的原創文章之外，轉載內容只為傳遞更多信息，并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題，請及時通過電子郵件或電話通知我們，以便迅速采取適當措施，避免給雙方造成不必要的經濟損失。聯系電話：010-82306118；郵箱：aet@chinaaet.com。