《電子技術應用》
您所在的位置:首頁 > 電源技術 > 解決方案 > ONSEMINCP125525W離線電流模式PWM控制器參考設計方案

ONSEMINCP125525W離線電流模式PWM控制器參考設計方案

2013-09-09

ONSEMI公司的NCP1255是一款soic-8封裝的堅固高性能離線高集成PWM控制器,輸入電壓范圍最高可達35V。該控制器具有過功率保護、掉電保護、輕載變頻、斜率補償、內建軟啟動、過載及短路自動定時恢復等功能。本文首先介紹芯片的簡介、特性、內部框圖及應用領域,并給出相應設計方案的設計原理圖、元器件列表及PCB元件布局圖。

The NCP1255 is a highly integrated PWM controller capable of delivering a rugged and high performance offline power supply in a SOIC−8 package. With a supply range up to 35 V, the controller hosts a jittered 65−kHz switching circuitry operated in peak current mode control. When the power on the secondary side starts to decrease, the controller automatically folds back its switching frequency down to a minimum level of 26 kHz. As the power further goes down, the part enters skip cycle while freezing the peak current setpoint.

To help build rugged converters, the controller features several key protective features: a brown−out, a non−dissipative Over Power Protection for a constant maximum output current regardless of the input voltage, two latched over voltage protection inputs – either through a dedicated pin or via the Vcc input − and finally, the possibility to externally adjust an auto−recovery timer duration.

The controller architecture is arranged to authorize a transient peak power excursion when the peak current hits the limit. At this point, the switching frequency is increased from 65 kHz to 130 kHz until the peak requirement disappears. The timer duration is then modulated as the converter crosses a peak power excursion mode (long) or undergoes a short circuit (short).

NCP1255主要特性:

• 65−kHz Fixed−frequency Current−mode Control Operation with 130−kHz Excursion
• Internal and Adjustable Over Power Protection (OPP) Circuit
• Adjustable Brown−Out Protection Circuit
• Frequency Foldback down to 26 kHz and Skip−cycle in Light Load Conditions
• Adjustable Slope Compensation
• Internally Fixed 4−ms Soft−start
• Adjustable Timer−based Auto−recovery Overload/Short−circuit Protection
• 100% to 25% Timer Reduction from Overload to Short−circuit Fault
• Double Vcc Hiccup for a Reduced Average Power in Fault Mode
• Frequency Jittering in Normal and Frequency Foldback Modes
• Latched OVP Input for Improved Robustness and Latched OVP on Vcc
• Up to 35−V Vcc Maximum Rating
• Extremely Low No−load Standby Power
• This is a Pb−Free Device

NCP1255應用:

• Converters requiring peak−power capability such as printers power supplies, ac−dc adapters for game stations.

 
圖1. NCP1255內部方框圖

NCP1255方案介紹:

The NCP1255 features several novelties compared to the NCP1250 previously released. The key feature of this component lies in its ability to push the switching frequency as the converter experiences a sudden power increase.However, this available extra power delivery can only be maintained for a certain amount of time. Beyond this duration, the controller gives up and enters an auto-recovery mode. This mode is perfectly suited for converters supplying highly variable loads such as Haswell-based notebook adapters or inkjet printers to cite a few possible examples.

General Description

The part is encapsulated in a SOIC−8 package but a reduced-feature set version (no brown-out and timers are internally set), the NCP1254, also exists in a tiny TSOP−6 package. Featuring a low-power BiCMOS process, the die accepts to work with VCC levels up to 35 V, safely clamping the drive voltage below 12 V. With its 15 _A start-up current, a high-value resistive network can be used in offline applications to crank the converter, naturally minimizing the wasted power in high-line conditions. In nominal load operations, the switching frequency of this peak-current mode control circuit is 65 kHz.

When the power demand goes up, the controller increases the peak current setpoint until it reaches the upper limit (0.8 V over Rsense, no opp). At this point, the output power demand increase can only be answered by further shifting the switching frequency up until it reaches another limit, 130 kHz. The maximum power is thus obtained at this moment. On the contrary, in light-load operations, the part linearly reduces its switching frequency down to 26 kHz and enters skip cycle as power goes further down. This mode of operation favors higher efficiency from high to moderate output levels and ensures the lowest acoustic noise in the transformer. To improve the EMI signature, a low-frequency modulation brings some dither to the switching pattern. Unlike other circuits, the dither is kept in foldback and peak excursion modes, continuously smoothing the noise signature.

The part hosts several new protection means such as an auto-recovery brown-out circuit. It is adjustable via a resistive divider. A double hiccup on the VCC brings down the average input power while in auto-recovery fault mode.

Board Description

The application schematic that appears in Figure 1 has been optimized to limit the leakage inductance losses and maximize the efficiency. For this purpose, the RDC clamping network has been replaced by a TVS-based circuitry, leaving enough swing to the 800 V MOSFET. Again, a 600 V type could have been used but would have hampered the drain voltage dynamics at turn off. A capacitor in parallel with the TVS limits its peak current at the switch opening and helps softening the radiated noise. Besides its excellent performance in standby, the TVS approach helps to maintain a safe clamping level given the wide output power excursion.

The chip supply is brought in via pin 6. Please note that the start-up resistances, besides cranking the controller, also perform the X2 discharge function for free. Upon start-up, for a voltage less than 18 V (typical), the internal consumption is limited to 15 _A maximum. It suddenly changes to a few mA as the controller starts to drive the 800 V MOSFET at 130 kHz when VCC reaches 18 V. The auxiliary voltage can go down to around 9 V before the controller safely stops the switching pulses. The first VCC capacitor C3 must be sized so that the auxiliary winding takes over before the UVLO is touched. The auxiliary winding is tailored to deliver an auxiliary voltage above 12 V and it drops to 10 V in no-load conditions. This guarantees a good no-load standby power performance as you will read below. A low-valued resistance (R13) limits the voltage excursion on this auxiliary voltage in short circuit situations.

Regulation is ensured by pulling down the dedicated pin via an optocoupler, driven from the secondary side by a NCP431. This new device does not require a 1 mA bias current as it was the case with the classical TL431. The absence of this bias current greatly contributes to reducing the no-load standby power.

NCP1255方案原理圖:

  

圖2. NCP1255方案原理圖

NCP1255方案材料清單:





PCB元件布局圖:


 


本站內容除特別聲明的原創文章之外,轉載內容只為傳遞更多信息,并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題,請及時通過電子郵件或電話通知我們,以便迅速采取適當措施,避免給雙方造成不必要的經濟損失。聯系電話:010-82306118;郵箱:aet@chinaaet.com。
亚洲一区二区欧美_亚洲丝袜一区_99re亚洲国产精品_日韩亚洲一区二区
国内精品亚洲| 一区二区三区视频在线观看| 欧美破处大片在线视频| 久久福利影视| 亚洲欧美中文日韩v在线观看| 日韩天堂在线视频| 91久久精品美女| 亚洲第一精品福利| 久久av免费一区| 欧美在线视频一区二区三区| 性欧美xxxx大乳国产app| 亚洲一区二区成人| 亚洲一区二区黄| 亚洲图色在线| 亚洲午夜在线观看| 亚洲一区二区三区精品视频 | 亚洲欧美国产精品专区久久| 亚洲图片欧洲图片av| 亚洲视频精品在线| 一区二区三区精品国产| 一本高清dvd不卡在线观看| 亚洲毛片av| 制服丝袜亚洲播放| 亚洲在线不卡| 性欧美长视频| 亚洲成人自拍视频| 亚洲精品少妇网址| 正在播放亚洲| 亚洲欧美日韩电影| 欧美中文在线观看| 久久最新视频| 欧美精品一区二区视频 | 欧美午夜免费| 国产精品一级在线| 国产亚洲精品久久久| 国产一区二区三区久久精品| 一区二区三区亚洲| 亚洲日本一区二区三区| 99精品99久久久久久宅男| 亚洲视频成人| 欧美一区二区三区视频在线| 亚洲大片在线| 99热在线精品观看| 亚洲在线网站| 久久久99精品免费观看不卡| 噜噜噜噜噜久久久久久91| 欧美成人一区二区在线| 欧美揉bbbbb揉bbbbb| 国产欧美日韩视频一区二区三区| 韩国福利一区| 亚洲精品国精品久久99热| 亚洲色图制服丝袜| 欧美在线亚洲| 一区二区国产日产| 久久岛国电影| 欧美激情久久久久| 国产精品美女诱惑| 精品成人在线| 亚洲美女视频| 欧美亚洲一区| 夜久久久久久| 久久国产66| 欧美精品一线| 国产三级精品在线不卡| 91久久久久久久久| 亚洲欧美日韩国产| 日韩视频精品| 久久国内精品自在自线400部| 免费亚洲电影在线| 国产精品香蕉在线观看| 亚洲第一区在线| 亚洲网站视频福利| 亚洲国产精品成人久久综合一区| 亚洲一区二区在线免费观看视频| 久久久久久网址| 欧美人与性动交cc0o| 国产综合久久久久久鬼色| 夜夜嗨av色一区二区不卡| 久久爱91午夜羞羞| 亚洲一区免费视频| 欧美xart系列高清| 国产日韩欧美在线| 一区二区国产日产| 亚洲日本成人在线观看| 久久精品毛片| 欧美视频日韩| 亚洲国产精品一区| 欧美在线1区| 亚洲免费视频网站| 欧美大片在线看| 国产曰批免费观看久久久| 中文国产一区| 亚洲精品自在久久| 久久精品一二三区| 国产精品伊人日日| 日韩性生活视频| 亚洲精品国产拍免费91在线| 久久精品国亚洲| 国产精品jizz在线观看美国 | 尤物yw午夜国产精品视频明星| 亚洲一区二区免费视频| 99这里只有精品| 免费视频亚洲| 国内精品国语自产拍在线观看| 亚洲午夜在线视频| 一区二区三区视频在线观看| 美国十次了思思久久精品导航| 国产午夜精品理论片a级大结局 | 亚洲欧美日韩国产中文| 亚洲天堂偷拍| 欧美日韩免费网站| 亚洲国产精品一区二区久| 亚洲国产欧美不卡在线观看| 久久久久久噜噜噜久久久精品| 国产精品综合不卡av | 午夜电影亚洲| 亚洲欧美日韩在线| 欧美色区777第一页| 99re热精品| 日韩午夜在线电影| 欧美韩日高清| 91久久国产综合久久91精品网站| 亚洲国产91| 久久这里只有| 一区三区视频| 亚洲国产一区在线| 免费日韩成人| 亚洲国内欧美| 亚洲最新视频在线| 欧美日韩国产专区| 日韩视频在线观看一区二区| 一区二区三区产品免费精品久久75 | 国产综合网站| 亚洲欧美日韩综合aⅴ视频| 中文精品视频| 欧美日韩在线一区二区| 国产精品99久久久久久久vr | 中文亚洲视频在线| 午夜精品偷拍| 国产精品视频九色porn| 亚洲欧美区自拍先锋| 久久成人亚洲| 娇妻被交换粗又大又硬视频欧美| 最新国产の精品合集bt伙计| 欧美国产精品中文字幕| 亚洲伦理一区| 亚洲欧美日韩国产| 国产视频久久| 91久久久一线二线三线品牌| 欧美国产精品| 亚洲少妇中出一区| 欧美在线观看视频在线| 一区福利视频| 一本一本a久久| 国产精品免费aⅴ片在线观看| 性欧美8khd高清极品| 免费看黄裸体一级大秀欧美| 最新日韩在线| 亚洲欧美成aⅴ人在线观看| 国产夜色精品一区二区av| 91久久在线观看| 欧美午夜国产| 欧美诱惑福利视频| 欧美精品偷拍| 亚洲欧美三级在线| 免费短视频成人日韩| 一区二区欧美激情| 久久精品国产亚洲高清剧情介绍| 亚洲国产另类久久久精品极度| 亚洲视频在线观看视频| 国产一区久久| 一区二区三区欧美| 国产在线欧美| 一区二区三区日韩| 国产一区高清视频| 在线亚洲国产精品网站| 国产精品私人影院| 91久久精品美女高潮| 国产精品国产三级国产普通话99| 欧美在线综合| 国产精品theporn88| 久久精品一区中文字幕| 欧美色一级片| 亚洲第一狼人社区| 欧美天天综合网| 亚洲福利免费| 欧美性天天影院| 最新国产精品拍自在线播放| 国产精品第三页| 亚洲日本成人| 国产人久久人人人人爽| 99re在线精品| 黄色成人在线网站| 亚洲自拍偷拍视频| 亚洲国产欧美一区二区三区同亚洲| 先锋影音一区二区三区| 亚洲全黄一级网站| 久久这里只有精品视频首页| 亚洲一级在线观看| 欧美日韩成人网|